Skip to content
Energy Links Ghana

Inverters & Solar

Harmattan Dust and Solar Panels: What It Costs and How to Clean Them

· 10 min read · Energy Links Ghana

The short answer. Harmattan dust costs you real generation, the loss is larger than most owners assume, and the dry season removes the rainfall that would otherwise wash it away — so the worst soiling of the year arrives exactly when nature has stopped cleaning for you. Cleaning helps. Cleaning carelessly causes scratched glass, scale deposits, cracked modules and, occasionally, electric shock.

The number, with its limits stated. The most directly relevant measurement we could find for Ghana is a 2016 KNUST master's thesis by Bernard Owusu-Brown, The effect of settling harmattan dust on photovoltaic modules in Walewale, Northern Ghana. Over four months from November 2014 to February 2015, on a 50W monocrystalline module, settling dust reduced power output by 28.7 percent and panel efficiency by 5.6 percent.

That is one module, at one site in northern Ghana, across one harmattan. It is not a national figure and should not be treated as one. Northern Ghana sits closer to the dust source than Accra does, and your roof is not Walewale. What the thesis establishes is the order of magnitude and the mechanism — and the mechanism is the part that should change how you maintain a system.

Two separate losses, and only one of them can be cleaned

This is the distinction that most cleaning advice misses, and the KNUST work makes it explicit.

1. Suspended dust in the air. During harmattan, dust in the atmosphere scatters sunlight before it ever reaches your array. Less irradiance arrives at the glass. You cannot clean this away. Spotless panels on a heavy harmattan day still produce less than the same panels on a clear day, and the owner who has just cleaned and sees no improvement often concludes, wrongly, that the panels are faulty.

2. Settled dust on the glass. This physically blocks the cells, which is the loss the thesis quantified at 28.7 percent at that site. This one you can clean, and it accumulates steadily through the dry season.

So the honest expectation after a clean is: you recover the settled-dust component, not the atmospheric one. If you want to know what cleaning is actually worth on your own roof, record daily generation for a week before and a week after — your inverter or monitoring app will show it. That measurement is worth more than any percentage in any article, including this one.

What we deliberately are not telling you

Two things, because the gaps matter.

The regional research literature exists but we could not read it. There is a peer-reviewed paper directly on this subject — Isaacs, Kalashnikova, Garay, van Donkelaar, Hammer, Lee and Wood, Dust soiling effects on decentralized solar in West Africa, Applied Energy volume 340, article 120993, 2023. We confirmed those bibliographic details from indexing databases, but the article is closed access and we could not retrieve its abstract or text. We are therefore not quoting any figure from it. It is the right paper for anyone who wants the regional modelling, and we would rather name it and admit we could not open it than paraphrase numbers at second hand.

The dramatic percentages in circulation are mostly unsourced. Figures far higher than the KNUST measurement appear in practitioner articles about Ghanaian arrays, generally with no stated measurement method. They may well be right for particular badly-sited installations. They are not evidence, and we will not repeat them as though they were.

Why rain does not solve it here

Most module cleaning guidance is written for climates where rain does the work. First Solar's own Module Cleaning Guidelines states the standard position plainly: "For many installations, rainfall should be sufficient to remove any lighter soiling. In locations with heavy soiling, properly timed module cleaning can improve energy yields."

Read that against the Ghanaian calendar. Harmattan is the dry season. The soiling peaks precisely during the months when there is no rain to remove it, and the first rains that follow often arrive as a light shower that turns accumulated dust into streaked mud — frequently worse than before. Ghana is unambiguously a "location with heavy soiling" where "properly timed module cleaning" is the manufacturer's own recommended answer.

There is a second local point. Panel ratings are measured at a cell temperature of 25 degrees Celsius, which an Accra roof passes well before mid-morning, so real output already sits below the nameplate for most of the day. Soiling stacks on top of a heat loss you already have. Mounting that lets air move behind the modules recovers some of it — see hybrid or off-grid solar for how the local conditions derate a design.

How to clean panels without damaging them

The guidance below is drawn from First Solar's published cleaning guidelines for its own modules. Those are frameless thin-film products, so some points are specific to them — always check your own module's installation manual. The safety and water-chemistry guidance transfers directly, and it is more specific than anything you will find in general advice.

Safety first, and this is not a formality. The document is explicit that an array is dangerous to clean: "The voltage and current present in an array during daylight hours" is "sufficient" to "cause a lethal electrical shock", cracked or broken modules present a shock hazard through leakage currents, and the risk increases when modules are wet. It directs that only properly trained personnel who understand the risks of applying water to electrical components should clean modules, wearing electrically insulating protective equipment, and notes that professional cleaning services trained to work on live electrical systems can be hired.

Inspect before you touch anything. Check for cracks, damage and loose connections first. Do not clean a cracked module.

Clean in the dark, or close to it. The recommended window is "from dusk to dawn when production is not affected and risk of electrical shock hazard is minimized", and the ideal time is during low light when production is lowest. Early morning before the roof heats up is the practical Ghanaian version of this.

Match the water temperature to the panel. The guideline is direct: do not apply water more than 20 degrees Celsius warmer or colder than the module surface temperature. This is the single most relevant rule for Ghana. A roof that has been in full Accra sun is very hot. Cold water from a tank onto hot glass is a thermal shock, and thermal shock cracks modules. It is the most common way a well-intentioned owner destroys a panel.

Water quality matters more than you would think. Fresh water below 1,500 mg/L total dissolved solids may be used. Reverse-osmosis water gives the best results; otherwise tap water of low mineral content, with total hardness below 75 mg/L, or deionised water. Where hard water must be used — total hardness between 75 and 180 mg/L — it has to be squeegeed off to prevent scale building up on the glass. Scale is a permanent soiling you have added yourself.

Pressure limits. Water pressure must not exceed 35 bar (500 psi) at the nozzle, and pressurised water must not be sprayed directly at the module's sealed interfaces, junction box, edge seal or connectors.

Chemicals. If a detergent is needed, it must be mild, non-abrasive and non-caustic, with the final water-and-detergent mix between pH 6.5 and 8.5. Do not use abrasive cleaners or degreasers, and do not use solutions containing hydrochloric acid, D-Limonene, ammonia or sodium hydroxide. That rules out most household bleach and most strong cleaning products sold in Ghanaian shops.

Tools. For heavier soiling, a non-conductive nylon or similar brush, a sponge or another mild agitating method may be used with caution. Tools must not be abrasive to glass, EPDM, silicone, aluminium or steel, and must be made of non-conductive material to reduce shock risk. Do not brush or clean the back of a module — you risk stressing the lead wires and junction box. For dry cleaning, that document allows soft cloths or mops up to six times a year and prohibits bristle brushes, sponges or squeegees dry.

And the point behind all of it: cleaning is an operation with real risk to the asset and to the person doing it. The guidance exists because cleaning activities themselves "create risk of damage to the modules and array components, as well as the potential for electric shock".

A sensible schedule for Ghanaian conditions

There is no universal interval, and anyone who gives you one without seeing your site is guessing. What follows is a structure rather than a number.

  1. Through harmattan, from roughly November to February, inspect frequently and clean on evidence. This is the accumulation season. Look at the glass and look at your generation figures.
  2. Clean on measured loss, not on the calendar. If your output has fallen and the weather has not, the dust is the likely cause. If output has fallen and the air is thick with haze, wait — you are seeing the atmospheric component and cleaning will not fix it.
  3. Clean again after the first real rains. Light rain on heavy dust streaks rather than washes. Inspect afterwards rather than assuming the rain did the job.
  4. Keep a simple log. Date, what you did, and the generation figures either side. After one dry season you will know your own site's interval, which is worth more than any published average.
  5. Check the rest of the installation while you are up there. Connectors, cable ties, mounting bolts, shading from a new structure or a growing tree, and dust blocking the ventilation of the inverter or combiner enclosure.

Harmattan dust is hard on more than panels. If you also run a generator, the air-side service intervals shorten in the same season, which is covered in generator servicing schedule.

Frequently asked questions

How often should I clean my solar panels in Ghana?

More often in harmattan than outside it, and on evidence rather than a fixed interval. Watch your generation figures, inspect the glass, and clean when the two agree that dust is costing you output. Sites near untarred roads, construction or heavy traffic need it considerably more often.

Do I need to switch the system off before cleaning?

An array is live in daylight, which is why the manufacturer guidance points to cleaning in low light and to trained personnel in insulating protective equipment. Follow your own inverter and isolator procedure, and if you are unsure, this is work to hire rather than attempt.

Can I use soap and a pressure washer?

A mild, non-abrasive, non-caustic detergent within the stated pH band, yes. Strong household cleaners, bleach, ammonia and degreasers, no. Pressure is capped at 35 bar at the nozzle, and never aimed at junction boxes, connectors or edge seals.

Does dust permanently damage panels?

Dust itself generally does not. The things that do permanent damage are what people use to remove it: abrasive brushes that scratch the glass, hard water left to dry as scale, and cold water on hot glass cracking the module.

My panels are clean but output is still down. Why?

Most likely the atmospheric component — suspended harmattan dust reducing the light arriving at the array. Heat is a second cause. A genuine fault is a third, and a monitoring log is how you tell the three apart.

Have it cleaned, checked and measured properly

Cleaning is only worth doing if you know what it recovered. Our engineers service and support the systems we install — inspecting the array, cleaning it correctly for the module type, checking connectors and ventilation, and comparing generation before and after so you can see what the dust was actually costing you.

Contact us to arrange a site visit or discuss a servicing arrangement, or browse the solar, inverter and power equipment we stock.

Need help choosing the right equipment?

Our engineers will size it against your actual load, not a guess.

Talk to us